Відео

omg, please don't do it again, you are too far from doing it right.

What I really needed to see is how to reassemble the valve: getting the o-ring in the correct place was not really obvious but I finally figured it out..that the o ring goes between the cone-shaped piece bigger side and the far inside of the valve body...

A very informative video. Enjoyed.

Good job mate!

Why would anyone make a video showing how they struggle with electrical work.

That pin that goes in and out with the water level is making a buzzing sound on my toilet when flushing and seems to get stuck in when I flush, I was wondering if I can just replace the pin and is there a spring inside it that gives it its springness

A truly crap piece of equipment ... They are fine when they are working but cheaply made .. Ive had 2 that have failed with the adjustment no longer working and the metal casing cracking on both ... Was only used in my own garden (not commercially) ..

Thanks for the video, perfectly explained.

One of my mates who is an electrician, says all you need to get an EV charging at 32amps is the following; He did also mention a UPS over an RCD as the voltage can still increase;;;; 32amp commando socket 3 pole isolated 40 amp 4mm twin and earth Y

If you did a 32 amp for an EV commando, would you do the same thing?

Is the light IP rated?

Thank you.

Perfect simple explanation, First realised I had a problem when water was running down the brickwork from the overflow pipe outside. I had the opposite issue - too high a water level in the toilet tank. Sure enough the water was spilling over into the overflow tube. I adjusted silver nut/screw as recommended. Thanks Garry!

Please, for the love of god, tell me you're not an actual electrician.

This has to be a wind up. 😂

"Bog Standard" well played

Absolute torture watching this 😂 are you DIY or you doing this for a living

Hang in there. These valves are commonly wrongly described as an isolation valve in the plumbing industry. They are correctly known as a service valve, to allow short term tuning or replacement of other more properly pressure rated valve components, such as a gate valve, or lever valve. They can be handy but really not a great solution.

Why didn’t you strip the cable by pulling the cpc

Are you an electrician

I had a 2006 focus with same issues blew 2 turbos, ended up trading it in for a Prius Hybrid and covered over 300k in it with zero issues. Sorry Henry Ford I have lost my faith in the Ford Motor Company.

Ive got the same problem pal in my kitchen. By any chancebincan just apply a new fresh plasterboard over the old wall ?

Hello Garry! I just saw your pantry removal video & i noticed this was posted a few years back. IT'S KILLING ME THAT I CAN'T FIND AN UPDATE OF HOW YOU FINISHED OFF THE WALL & HOW MUCH BIGGER YOUR KITCHEN MUST BE NOW. WOULD YOU SAY THE KITCHEN WORKS MORE EFFICIENTLY NOW? Did you decide on upper & lower cabinets? i know you mentioned wanting to extra surface counter space. 100% agree. We're in the U.S. & oddly enough this is the biggest kitchen I've ever had. The home is 4 bdrm 2 bth about 2700 square feet. YET the builder or designer created a "Pantry" that's quite literally the size of a broom closet. 😂. Common sense would say anyone who needs 4 bedroom may need to FEED the people living in those bedroom. 😂 Anyway, GREAT JOB& WE WOULD ALL LOVE TO SEE AN UPDATE OF THE NEW LAYOUT. PLZ POST A VIDEO OR SOME PICTURES. PLZ& TY

I'm from the US, it's crazy seeing how well-made other countries houses are made. Here in Texas, there'd be some drywall, 2x4s, and maybe some insulation. Very insightful!

This is very useful thanks. I liked the way you point out the relevant parts when you mention their names and cover the really important stuff like not over tightening on the nuts on the pipework underneath the toilet. Most of the vids on here are for side entry filler systems so not relevant to me. The camerawork could have been in better focus ! However i did like the slower pace so its easier to follow what you are saying. On many other guidance vids the guys talk too fast, or try to crack too many jokes. Then its harder to follow the key points. Unfortunaltey all this was in vain in my particular case as the plastic nut under the toilet was far too tight and far too difficult to reach - due to the toilet bing fitted too close to the side wall. So i'll have to call a plumber and get the whole cistern replaced with a more modern side fed filler pipe. Many thanks anyway for putting this on UA-cam. I did learn some useful stuff !

You are going to either get black mould or damp now 😱😱😱

Nooo…Nooo, do not ever cover an air brick vent

i have one but not tried thick branches, I had a problem with not starting and found the hexagon screws in the front plate had come loose. The screws hit switches that isolate the machine. Just check now and again to make sure they are tight. (not overtight).

Great advice thank you!!

It's still there Gerry..

We have the same style pantry in our kitchen. Except we have a lintel above the door, which goes into the supporting wall next to it. I'll need to get it inspected, before carefully removing it. Good video.

This is the second one for the basement bat. ua-cam.com/users/postUgkxOuLt8IL_GxhhaK8DBuKEL-zV0UJVpWZn , works great

Thank you Garry

Great job

Hi there i have fitted a side entry fill valve, there doesnt seem to be sealing washer on the inlet union pipe, is there supposed to be a fibre or rubber washer, it weeps a bit i have put a load of ptfe tape round ot, also when it fills up there is a horrible groaning noise for about 15 seconds.....any advice Please Fred in Essex.

You f*cked it mate.

How do you take out the black pin

Very good explanation !

Does anyone know if the blades can be removed for sharpening? I would think that after a while the blades would start to dull a bit as with most shredders. Cheers.

Wow, nice job! I'm getting ready to redo our kitchen pantry, too. Im in the US, I cant believe all that breeze block, first time Ive seen that! Cant believe you were able to do get it out. Great!Off topic, but I love that brick by the bike!

It will not flow out the cistern if it fills too much! The water will escape through the siphon bottle and into the toilet. That is why there is no visible overflow apparent.

very good video, thanks for ur time , god bless u

Is it still working my einhell was quieter I think Does it dismantle for winter with little tools

You blades are not set. Turn the blue knob . You can see the wood is snaking through into the clear bi

Hi can I drive my ford ka without a thermostat?

Great vid, I wasted hours not being able to adjust the screw enough to make the water stop. Once I saw you explain about the use of a screw driver on the end of the black pin I sorted it in 5 mins. Should have watched your vid first!!

Thanks, my over flow pipe was leaking and I think I've just fixed it by tightening the screws on the arm of the float, saving the cost of a plumber and metered water bill!

I'm on my 3rd machine in less than a month. First one was great proper little chomper but then the thread on the counter plate blade stripped and jammed so couldnt undo it I took it back to SF and the staff member was fantastic. Offered me a refund or a replacement no trouble at all orbeit I was s little concerned the same thing may happen again as the bolt just isn't strong enough. I took the replacement as I still had work to do. I took the replacement and literally 20 minutes into working the adjuster knob stopped turning and jammed... I was so frustrated as the machine really does a great job at shredding. I took the machine back two days later and again explained what had happened. The staff on this occasion couldn't have been any different. The assistant looked at me as if I'd done it deliberately and question how it had happened. She hadn't git s clue how the thing worked but clearly thought I'd done it deliberately. I asked if I could have one from another batch as possibly this batch had a simple fault of a dodgy bolt. But I was informed she had no idea how the batch system worked. I really didnt want another only to bring it hack again in s week or so with the same issue but still has 6 conifers to take down. Eventually she brought a replace6to the counter and opened it up before I even agreed to take it. She then insisted on checking the counter blade knob showing me it worked before I took it... I'm only hoping now the same thing dont happen again and gave even purchased a replacement m10 bolt from another supplier as I just done feel the bolt supplied I'd upto the job... Any one else had this problem???

Yay Thankyou after faffing about all morning watching other videos which didn’t show the right valve I’ve got. I found yours I was about to throw my girlie spinners out my pram and yay I’ve done it. Thankyouuuuuuuu

I must be doing something wrong, mine tends to crush instead of shred, I'm assuming you can use freshly cut material, thinking now I should have went for the spinning blade type, they are more expensive.